Yukon Gear & Axle
Yukon Gear & Axle PK GM55CHEVY Pinion install Kit For GM 55P and 55T Diff
Yukon Gear & Axle PK GM55CHEVY Pinion install Kit For GM 55P and 55T Diff
Couldn't load pickup availability
Photographs show a representative part from this product family. The axle model, gear ratio and spline count in the specifications below are what define this exact part number.
Genuine Yukon Gear & Axle part.
Yukon Pinion Installation Kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings and races can be reused. This kit features Timken bearings and races along with high-quality seals and small parts. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your gear set.
Key Features
- Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush
- This kit features Timken bearings and races along with high-quality seals and small parts
Fits These Vehicles
- Fits 1955-1964 Chevrolet Bel Air
- Fits 1958-1964 Chevrolet Biscayne
- Fits 1960-1964 Chevrolet C10 Pickup
- Fits 1962-1964 Chevrolet Chevy II
- Fits 1956-1962 Chevrolet Corvette
- Fits 1959-1960 Chevrolet El Camino
- Fits 1964 Chevrolet El Camino
- Fits 1958-1964 Chevrolet Impala
- Fits 1960-1964 Chevrolet K10 Pickup
- Fits 1958-1961 Chevrolet Nomad
- Fits 1960-1964 Chevrolet Suburban
- Fits 1955-1958 Chevrolet Truck
- Fits 1960 Chevrolet Truck
- Fits 1964 GMC G1500
- Fits 1960-1964 GMC Suburban
Please verify exact fitment for your trim and engine before ordering.
Specifications
- Brand: Yukon Gear & Axle
- Manufacturer Part Number: PK GM55CHEVY
- Type: Differential Pinion Bearing Kit
Images are for illustrative purposes. The product you receive may differ in finish or packaging from the photograph.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Share
🛡️
Manufacturer's Warranty — Yukon Gear & Axle
▾
Manufacturer's Warranty — Yukon Gear & Axle
Yukon Gear & Axle warrants to the original retail purchaser that its products are free from defects in materials and workmanship, and the term is set by product line rather than by one figure for the whole catalogue. Ring & pinion gear sets, carriers, yokes, install kits (BK, MK, PK, YK), spider gear kits, tools and YP-series parts carry one (1) year; Positraction differentials carry one year and exclude premature clutch wear and abuse. Zip Lockers carry six (6) years and Grizzly Lockers one year, each with collateral parts and labor coverage up to $2,000 on the terms Yukon publishes. 1541H front and rear axles carry ten (10) years, while 4340 chromoly axles (YA W series), spools, Super Joints, YHC drive flanges, Hardcore locking hubs and Hardcore diff covers carry a Limited Lifetime warranty for as long as the original purchaser owns the vehicle the part was first installed in (not transferable). Coverage assumes the product was installed and maintained per Yukon instructions and not modified, abused or damaged in an accident, and Yukon may void the warranty on vehicles running tires larger than its Maximum Recommended Tire Size for that axle. On a verified defect Yukon will repair or replace the product at its choice. Labor, road service, loss of vehicle use and other incidental or consequential damages are excluded, as is axle damage caused by the failure of a non-Yukon component. Yukon also sells an optional Yukon Extended Service (Y.E.S.) plan that upgrades select products to lifetime coverage; it must be purchased within 30 days of ordering the Yukon product. This warranty gives you specific legal rights, and you may have other rights that vary from state to state.
Warranty terms are set by the manufacturer and may change. Full details and claims are handled directly by Yukon Gear & Axle. Contact us if you need help with a warranty claim.

Q&A
No questions yet. Be the first to ask!