• Torque Solution Braided Fuel Line Kit for -6 Aeromotive FPR & Flex Fuel Kit - 02-14 Subaru WRX
  • Torque Solution Braided Fuel Line Kit for -6 Aeromotive FPR & Flex Fuel Kit - 02-14 Subaru WRX
  • Torque Solution Braided Fuel Line Kit for -6 Aeromotive FPR & Flex Fuel Kit - 02-14 Subaru WRX
1 3

Torque Solution

Torque Solution Braided Fuel Line Kit for -6 Aeromotive FPR & Flex Fuel Kit - 02-14 Subaru WRX

Torque Solution Braided Fuel Line Kit for -6 Aeromotive FPR & Flex Fuel Kit - 02-14 Subaru WRX

$ 232.96
$ 256.26 $ 232.96
Free shipping on orders over $99 (contiguous U.S.) — flat $10.99 under $99. Shipping details
✓ In Stock • Only 1 left

Torque Solution Braided Fuel Line Kit for -6 Aeromotive FPR and Cobb Flex Fuel Kit is a perfect complement to go along with our Top Feed Fuel Rails. This kit utilizes the OEM hard lines on your Subaru and is supplied with our -6 AN quick connect fittings for a clean plug and play install. Also supplied with the necessary -6AN quick connect fittings to incorporate your existing Cobb Flex Fuel Kit. This setup is perfect for anyone looking to make up to 600 whp (proper fuel pump setup required). Our kit is designed to allow you to setup your fuel system in parallel to ensure each cylinder receives optimal fueling. All our fittings come black anodized and are compatible with all fuel types such as E85. Works with the Torque Solution Top Feed Fuel Rails or any other fuel rail that accepts -8an ORB fittings.

  • 6061 Billet Aluminum -6an Fittings
  • Black Anodized
  • Compatible with all fuel types such as E85
  • Limited Lifetime Warranty

Kit Includes:

  • 13ft -6 Black Nylon Braided Rubber Hose
  • 6an T-Adapter (1)
  • 6an Straight Hose Adapter (5)
  • 6an 90 Degree Hose Adapter (9)
  • 6an Male to 5/16" SAE Quick-Disconnect Female Push-On EFI Fitting (2)
  • 6an Male to 3/8" SAE Quick-Disconnect Female Push-On EFI Fitting (2)
  • 6an to 8an ORB Fuel Rail Fittings (4)
  • 6an to 6an ORB FPR Fittings (3)
  • *Works perfect with Aeromotive A1000 -6 Fuel Pressure Regulator (sold separately).
  • *Converts your existing Cobb Flex Fuel Kit to quick connect fittings for a seamless install.
  • *This kit is designed to place the Flex Fuel Sensor after the regulator in order to utilize both inputs on the Aeromotive FPR.
  • **2002-2005 WRX / STI will need to use 12-14mm fuel line clamps at the fire wall instead of the AN fittings.

Vehicle Fitment

  • 2006-2013 Subaru Forester
  • 2002-2014 Subaru Impreza
  • 2007-2012 Subaru Legacy
  • 2015-2020 Subaru WRX STI

Please verify exact fitment for your trim and engine before ordering.

Manufacturer Part Number: TS-SU-6FLK-AM-FF

Images are for illustrative purposes only. Actual product may vary.

Emissions Note: This product is not CARB approved and is not legal for sale or use on pollution-controlled motor vehicles in California, or in states that have adopted California emission standards. It is intended for off-road / racing use only. It is the responsibility of the installer/end-user to ensure compliance with all applicable federal, state and local emissions regulations.

⚠ WARNING (California Proposition 65): This product can expose you to chemicals which are known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.

Manufacturer's Warranty — Torque Solution

Torque Solution offers a Limited Lifetime Warranty, but only on parts Torque Solution manufactures and only on items that are not wear-and-tear parts. Torque Solution names urethane (polyurethane), rod ends, bearings, pulleys and coil packs as wear items its warranty does not cover — so urethane bushings, inserts and endlinks are treated as consumables even where a listing shows a lifetime bullet, and Torque Solution recommends routine inspection. Thermal blankets are covered for one (1) year against manufacturing defects, while exhaust wrap carries no warranty at all because of how it is installed and used. A few electronic parts — Fast Response IAT sensors and PNP speed-density adapter harnesses — state a 1-year term on their own product listings; Torque Solution asks you to confirm on the individual product page that the part carries a warranty before filing. Claims are filed by the original purchaser with proof of purchase, a clear description of the fault and detailed photos; if approved Torque Solution repairs or replaces the part rather than refunding it, and shipping both to and from Torque Solution is the customer's responsibility. Coverage is voided by improper installation, exposure to an exhaust leak, saturation by fluids such as oil, coolant or fuel, or use beyond the part's listed specifications. Also excluded: anodizing (UV, heat and chemical detergents), environmental corrosion, damage to or from related vehicle components, and installation, removal or vehicle-downtime costs. Noise, vibration and harshness after fitting stiffer or solid components is expected and is not a valid warranty or return issue. Fitment is based on USDM vehicles unless noted — cross-compatibility with non-USDM cars is not confirmed — and Torque Solution products are intended for off-road / race use only, with none of them CARB legal. Torque Solution's own returns and exchanges window is 30 days from the receiving date on new, unused items, with shipping both ways covered by the purchaser.

Warranty terms are set by the manufacturer and may change. Full details and claims are handled directly by Torque Solution. Contact us if you need help with a warranty claim.

View full details

Q&A

0 answered questions

No questions yet. Be the first to ask!